Measuring Wind Using Anemometers & Wind Vanes

An error occurred trying to load this video.

Try refreshing the page, or contact customer support.

Coming up next: The Water Cycle: Precipitation, Condensation, and Evaporation

You're on a roll. Keep up the good work!

Take Quiz Watch Next Lesson
Your next lesson will play in 10 seconds
  • 0:02 Wind Measurement
  • 2:27 Velocity Anemometers
  • 4:51 Pressure Anemometers
  • 6:22 Lesson Summary
Save Save Save

Want to watch this again later?

Log in or sign up to add this lesson to a Custom Course.

Log in or Sign up

Speed Speed

Recommended Lessons and Courses for You

Lesson Transcript
Instructor: Amy Lange

Amy has taught university-level earth science courses and has a PhD in Geology.

You've likely seen anemometers and wind vanes many times around where you live but haven't associated them with the wind speeds you hear reported on the news. This lesson looks into how we determine wind speed and direction with modern technology.

Introduction to Wind Measurement

While most winds are benign, winds associated with destructive storms have the ability to cause property damage and other problems. Therefore, being able to measure and predict wind is important to our society in understanding possible wind damages and weather patterns. In this lesson, we're going to briefly cover the history of wind measurement and then delve into the technology we use to measure wind today.

There are two different devices for measuring the wind: wind vanes and anemometers. Wind vanes are an instrument for showing the direction of the wind. Wind vanes are much older technology than anemometers. The oldest known wind vane was on top of the Tower of the Winds in Athens, dating back to 48 B.C. Although the wind vane did not survive, the Tower of the Winds is still in present-day Athens.

There are writings that suggest that wind vanes may have existed in ancient Mesopotamia and ancient China at even earlier periods. Wind vanes became common in ninth century A.D. when the Catholic Church decreed that all churches should have a rooster as a symbol of a passage in the Bible. Since these churches already had wind vanes, the rooster was combined with the wind vane to create the extremely common rooster wind vanes still seen today.

An anemometer is a device used to measure wind speed. It is derived from anemos, which is the Greek word for 'wind.' Even though the word is derived from ancient Greek, we were not able to measure wind speed until 1450 when Leon Battista Alberti invented the first anemometer, which used a flat disk that would swing back and momentarily show the force of the wind perpendicular to that disk.

A more familiar anemometer is the cup anemometer, which was invented in 1846 by Irish scientist Thomas Romney Robinson. The wind caused the cups to rotate horizontally, which moved a series of wheels to record the rotations. The most recent anemometer technology is the sonic anemometer, which was invented in 1994. We'll delve further into both of these anemometers in this lesson because they're methods that are still commonly used.

Modern Velocity Anemometers

Modern anemometers can be classified as either a velocity anemometer or pressure anemometer based on the technology used to measure wind speed and direction. We're going to examine some of the common anemometers in both of these categories, starting with velocity anemometers.

Cup anemometers are still the most common wind measurement device at weather stations. They consist of three arms ending in hemispheric cups all at equal angles to each other. As the cups rotate in the wind, a copper wire in the vertical shaft causes a minor electrical field. The output voltage from the electrical field is directly correlated to wind speed.

Cup anemometers are preferred because they are cheap, easy to operate, and simple. However, the moving parts mean that they need to be replaced. Also, the cup anemometer won't tell you wind direction.

Hot wire anemometers are another style of anemometer that give you wind speed but very little directional information. In these instruments, a very thin wire is heated to a set temperature. The wind across the wire drops the temperature. The relationship between the temperature drop and wind speed is dependent on the type of wire and the starting temperature. These anemometers are preferred when you are measuring wind speed in a very tight space. Users must be wary to keep these clean at all times because they will become inefficient when the wire becomes dirty.

To unlock this lesson you must be a Member.
Create your account

Register to view this lesson

Are you a student or a teacher?

Unlock Your Education

See for yourself why 30 million people use

Become a member and start learning now.
Become a Member  Back
What teachers are saying about
Try it risk-free for 30 days

Earning College Credit

Did you know… We have over 200 college courses that prepare you to earn credit by exam that is accepted by over 1,500 colleges and universities. You can test out of the first two years of college and save thousands off your degree. Anyone can earn credit-by-exam regardless of age or education level.

To learn more, visit our Earning Credit Page

Transferring credit to the school of your choice

Not sure what college you want to attend yet? has thousands of articles about every imaginable degree, area of study and career path that can help you find the school that's right for you.

Create an account to start this course today
Try it risk-free for 30 days!
Create an account